GLOW
$109.00
GLOW is a multi-peptide research blend supplied in a single vial, with the full composition listed on the lot COA. Supplied as 70 mg total (10/10/50) of lyophilized powder in a sealed 3 mL vial, with a lot-matched Certificate of Analysis.
- Research use only Not for human or veterinary use
- Certificate per lot Published against the lot number
- Independently tested RP-HPLC with LC-MS identity
- Restricted sale 21+ qualified researchers only
Overview
GLOW is a pre-combined blend of three peptides in one vial. The label split of 10/10/50 gives the milligram amount of each component, for a total of 70 mg.
Research context
Blends of this type are used in preclinical research where several peptides are studied together, avoiding the variability of combining separate vials. The identity and amount of each component are confirmed on the lot-specific Certificate of Analysis.
Specifications
- Form: Lyophilized powder
- Quantity: 70 mg total (10/10/50)
- Composition: Three-peptide blend, 10/10/50 mg. See lot COA for component identities
- Container: 3 mL glass vial, sealed
- Storage: Minus 20 °C, dry and protected from light
- Documentation: Lot-specific Certificate of Analysis (identity and purity by HPLC-MS), matched to the batch number on the label
For laboratory research use only. Not a drug, food, cosmetic or medical device. Not for human or animal use of any kind. No information on this page is medical advice or dosing guidance.
| Color Palette | Mist/Navy |
|---|---|
| Dosage | 70 mg (10/10/50) |
Identity and chemistry
| Compound | GLOW research blend |
|---|---|
| Components | Multi-peptide blend, 70 mg total (10/10/50). Component identities are confirmed on the lot Certificate of Analysis. |
| Quantity per vial | 70 mg total (10/10/50) |
| Form | Lyophilized powder |
| Appearance | As recorded on the lot Certificate of Analysis |
| Purity specification | Lot-specific. The measured purity for each lot is reported on its Certificate of Analysis |
| Test methods | RP-HPLC for purity, mass spectrometry (LC-MS) for identity |
| Solubility for analytical use | Select the solvent according to your laboratory’s validated analytical method |
Molecular weights are average masses for the free peptide. The salt form and counter-ion content can vary between lots, so the Certificate of Analysis for your lot is the reference for identity and purity results.
What arrives with the order
- One sealed 3 mL glass vial per unit ordered, containing 70 mg total (10/10/50) of lyophilized powder
- A label showing the compound name, quantity and lot number
- A lot-specific Certificate of Analysis, available on this page and in the COA library
Identity and chemistry information for laboratory research use only.
On arrival
- Inspect: Check that the seal is intact and that the lot number on the label matches the Certificate of Analysis.
- Store: Move the sealed vial to minus 20 °C as soon as it is received.
- Protect: Keep the vial dry and away from direct light.
Lyophilized storage
GLOW is supplied as 70 mg total (10/10/50) of lyophilized powder in a sealed 3 mL glass vial. Lyophilized peptide material tolerates short periods at ambient temperature in transit. For storage beyond that, keep the vial sealed at minus 20 °C, dry and protected from light.
Both components are supplied together in one vial, so any solution prepared from it contains every component in the labeled ratio.
Before opening
Let the sealed vial reach room temperature before opening, ideally in a desiccator, so that moisture does not condense on the powder. Open and handle the vial under clean laboratory conditions.
Stock solutions
Prepare stock solutions, expressed in mg/mL, according to your laboratory’s validated protocol and the solubility of the compound. Divide the solution into single-use aliquots and store them frozen, avoiding repeated freeze-thaw cycles. Label each aliquot with the lot number and the date of preparation.
Disposal
Dispose of unused material and contaminated consumables as laboratory chemical waste, in line with applicable federal, state and local rules.
Laboratory storage and handling information only. No dosing or administration guidance is given or implied.
What purity specification does this lot meet?
Every lot of GLOW is tested for identity and purity by HPLC-MS before release. The measured purity for your lot is shown on its Certificate of Analysis, matched to the lot number printed on the vial label.
Where do I find the Certificate of Analysis for my vial?
Lot testing records appear on this product page. You can also search by compound name or lot number in the COA library.
How is this blend composed?
Each vial contains 70 mg total (10/10/50) of lyophilized powder, combined in a single vial. The composition of each lot is confirmed on its Certificate of Analysis.
What arrives with the order?
One sealed 3 mL glass vial per unit ordered, containing 70 mg total (10/10/50) of lyophilized GLOW. Each vial is labeled with the compound name, quantity and lot number, so it can be matched to its Certificate of Analysis.
How should the vial be stored when it arrives?
Move the sealed vial to minus 20 °C, dry and protected from light, as soon as it is received. The Storage and handling tab covers storage, opening, stock solutions and disposal.
Is GLOW for human or veterinary use?
No. GLOW is supplied strictly for in vitro laboratory research. It is not a drug, dietary supplement, food or cosmetic, has not been approved by the U.S. Food and Drug Administration, and must not be used in humans or animals. Sale is restricted to persons aged 21 or over who are qualified researchers or who buy on behalf of a research institution, laboratory or business.
Looking for something else?
Tell us the compound and quantity you are looking for and we will confirm availability and lead time. For research use only.
Contact Us
